SipDeviceConfiguration
Version 68 (Adrian Georgescu, 05/26/2012 03:42 pm)
1 | 65 | Adrian Georgescu | h1. SIP Device Configuration |
---|---|---|---|
2 | 1 | Adrian Georgescu | |
3 | 35 | Adrian Georgescu | There are thousands of SIP devices on the market, for how to configure them we advise you to consult the support forum of the device manufacturer. |
4 | 1 | Adrian Georgescu | |
5 | 35 | Adrian Georgescu | Please do not open a ticket related to how a particular device must be configured. |
6 | 1 | Adrian Georgescu | |
7 | 1 | Adrian Georgescu | Setup your SIP device as follows: |
8 | 1 | Adrian Georgescu | |
9 | 65 | Adrian Georgescu | h2. SIP Account Credentials |
10 | 1 | Adrian Georgescu | |
11 | 1 | Adrian Georgescu | Account credentials are used for authentication and authorization of SIP requests performed by the SIP device. |
12 | 65 | Adrian Georgescu | |
13 | 65 | Adrian Georgescu | Your SIP address is XXX@sip2sip.info replace XXX with the username chosen during the account enrollment. |
14 | 49 | Adrian Georgescu | |
15 | 51 | Adrian Georgescu | | Username| XXX| |
16 | 1 | Adrian Georgescu | | Password| YYY| |
17 | 52 | Adrian Georgescu | | Domain/Realm|sip2sip.info| |
18 | 1 | Adrian Georgescu | |
19 | 1 | Adrian Georgescu | Register must be turned On in order to receive incoming calls. |
20 | 1 | Adrian Georgescu | |
21 | 64 | Adrian Georgescu | If your SIP devices is smart enough, there is no need to set manually anything else than the above settings. If you need to manually fine tune the configuration read below. |
22 | 51 | Adrian Georgescu | |
23 | 64 | Adrian Georgescu | [[SipDevices|Specific SIP devices configuration]] |
24 | 1 | Adrian Georgescu | |
25 | 1 | Adrian Georgescu | h2. Outbound Proxy |
26 | 1 | Adrian Georgescu | |
27 | 62 | Adrian Georgescu | There are multiple SIP servers distributed in multiple geographic locations. To locate them, the SIP device must always perform DNS lookups as defined in SIP standard "RFC3263":http://www.ietf.org/rfc/rfc3263.txt (NAPTR + SRV + A DNS lookups) |
28 | 59 | Adrian Georgescu | |
29 | 62 | Adrian Georgescu | You should never set manually an IP address belonging to SIP2SIP server infrastructure into your SIP device as it may change. You must use proper DNS lookups instead of hardwiring these setting into your SIP device. |
30 | 38 | Adrian Georgescu | |
31 | 51 | Adrian Georgescu | | Host | Port | Protocol | |
32 | 51 | Adrian Georgescu | | proxy.sipthor.net| 5060| UDP | |
33 | 1 | Adrian Georgescu | | proxy.sipthor.net| 5060| TCP | |
34 | 1 | Adrian Georgescu | | proxy.sipthor.net| 5061| TLS | |
35 | 57 | Adrian Georgescu | |
36 | 63 | Adrian Georgescu | h2. TLS Settings |
37 | 60 | Adrian Georgescu | |
38 | 63 | Adrian Georgescu | You may use TLS transport, the SIP servers have a valid X.509 certificate issued by "RapidSSL":http://www.rapidssl.com corresponding to the proxy.sipthor.net hostname of the proxy. If the client does not RapidSSL certificate authority loaded, it may fail to validate the certificate. If the client allows it you can download the "RapidSSL root CA":http://www.geotrust.com/resources/root_certificates/certificates/Equifax_Secure_Certificate_Authority.cer into it. Turn TLS certificate validation off to circumvent the problem. |
39 | 34 | Adrian Georgescu | |
40 | 50 | Adrian Georgescu | |
41 | 51 | Adrian Georgescu | h2. XCAP Root |
42 | 51 | Adrian Georgescu | |
43 | 34 | Adrian Georgescu | If you use SIMPLE presence you need to set XCAP root: |
44 | 1 | Adrian Georgescu | |
45 | 54 | Adrian Georgescu | | XCAP Root | https://xcap.sipthor.net/xcap-root/| |
46 | 51 | Adrian Georgescu | |
47 | 51 | Adrian Georgescu | h2. MSRP Relay |
48 | 1 | Adrian Georgescu | |
49 | 68 | Adrian Georgescu | If you use SIMPLE instant messaging based on "MSRP":http://tools.ietf.org/html/rfc4975, a "relay":http://tools.ietf.org/html/rfc496 is available for helping traverse the NAT. You need to use the relay if you are the receiving party and you are behind a NAT-ed router. The MSRP relays can be found in the DNS by using SRV lookup for _msrps._tcp.sip2sip.info. |
50 | 53 | Adrian Georgescu | |
51 | 53 | Adrian Georgescu | h2. STUN Servers |
52 | 1 | Adrian Georgescu | |
53 | 56 | Adrian Georgescu | You may use STUN for ICE NAT traversal. The STUN servers can be found in the DNS by using SRV lookup for _stun._udp.sip2sip.info. |
54 | 56 | Adrian Georgescu | |
55 | 56 | Adrian Georgescu | h2. NAT Traversal |
56 | 56 | Adrian Georgescu | |
57 | 67 | Adrian Georgescu | SIP2SIP infrastructure is smart enough to handle the NAT traversal for both SIP signaling, RTP and MSRP media sessions. Practically, you should not set any NAT traversal features in the client as the chance of fixing things is much smaller than breaking them. |
58 | 56 | Adrian Georgescu | |
59 | 56 | Adrian Georgescu | * Do not use STUN for Register purposes |
60 | 56 | Adrian Georgescu | * Do not set your client to discover a global IP address |